Browse all practice questions for the EM4 Digital Electronics Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

EM4 Digital Electronics Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • A flip-flop in this design primarily serves what purpose?
  • For a three-bit word A, B, C, the parity bit P is defined as P = A ⊕ B ⊕ C; P is 1 if the number of ones is odd.
  • A logic probe is used to
  • An accumulator stores data currently being used by the ALU
  • Active probes can be ruined by
  • Which statement best describes how SRAM differs from DRAM?
  • Three common computer bus types are
  • Which combination forms the tiny datapath?
  • To mitigate a static-1 hazard in AB + A'C, which redundant product term could be added?
  • Read-only memory stands for?
  • Which device has a fixed OR network and a programmable AND array?
  • Define a shift register with serial input and serial output.
  • For a 4-bit ripple-carry adder, how many full-adder propagation delays determine the worst-case delay to the final carry output?
  • The expression A * B denotes which logic operation?
  • The ENIAC is one of the earliest electronic computers. What does ENIAC stand for?
  • Derive the sum and carry outputs of a full adder given inputs A, B, Cin.
  • Which CPU function interfaces the computer with peripheral devices?
  • RAM stands for
  • In numbering systems, what term describes the base used by the system?
  • Using a Karnaugh map, the minimized sum for f(A,B,C) with minterms 0, 2, 5, 7 is?
  • What is the effect of an input glitch in a sequential circuit?
  • Present the JK flip-flop truth table.
  • Write the truth table for a 3-to-8 decoder with inputs A, B, C.
  • Define a Karnaugh map.
  • Which component directly enables loading a specific register when the address matches?
  • Which statement about humidity and ESD danger is true?
  • Which device performs inversion on a digital signal?
  • Which diagram is used to illustrate the sequence of operations in a program?
  • If a gate drives more load capacitance, what is the effect on timing?
  • Which component of a computer microprocessor performs simple logic functions such as AND, OR, and XOR?
  • In an EAPROM, data can be changed
  • How can a 2-to-1 multiplexer be implemented from basic gates?
  • Which device is used to safely handle DIP ICs to prevent electrostatic damage?
  • Which encoding uses 8 bits per character?
  • Which statement describes Von Neumann architecture?
  • Provide an example of a static-0 hazard.
  • The MCU architecture where instructions and data use the same bus is?
  • Test points provide a means for conveniently and safely determining the operational status of equipment.
  • A logical pulser creates a timed pulse to
  • What does ESD stand for?
  • Which standard IC is commonly used to drive 7-segment displays from BCD input?
  • -5 in 8-bit two's complement is represented as:
  • Common logic probes cannot operate with voltages exceeding how many volts?
  • What is the general role of a parity bit in a data transmission?
  • Explain the concept of setup and hold constraints in flip-flops.
  • In binary notation, the value 100000 represents which decimal number?
  • Distinguish between a synchronous counter and an asynchronous (ripple) counter.
  • In ESD control, the resistor should be located at or near the point of contact with the benchtop.
  • Using a 2-to-1 multiplexer, implement the function F = A'B + AC. Which configuration correctly represents this function?
  • For a 3-to-8 decoder, when inputs are A=1, B=1, C=0, which output line is high?
  • What must occur for loading into a selected register to happen?
  • What is the characteristic equation of a D flip-flop?
  • What sequence does a 4-bit Johnson counter generate?
  • In Karnaugh maps, what does wrap-around adjacency mean?
  • The minimized expression f(A,B,C) = A'C' + AC covers which minterms?
  • What is the next-state table used for with respect to state diagrams?
  • A 1-to-4 demultiplexer has how many outputs?
  • In Boolean algebra, the expression A + B describes which operation?
  • If the address width is extended to 2 bits, how many registers could theoretically be addressed by the decoder?
  • A byte is composed of how many bits?
  • Which processor unit performs arithmetic and logic operations such as AND, OR, and XOR?
  • A precaution when using a logic probe is to
  • Which statement correctly defines the four types of shift registers: SIPO, PISO, SISO, and PIPO?
  • A NOR is which of the following?
  • What is the purpose of a decision symbol in a flowchart?
  • Which statement describes CMOS static power behavior?
  • What does a parity error indicate and how is it detected?
  • Which memory type is typically non-volatile and used for firmware storage in MCUs?
  • How is fan-out determined for a gate driving N identical inputs?
  • Which statement best describes the overall data flow?
  • In a Moore machine, on what does the output depend?
  • A three input NAND has two low inputs and a high input; the output will be
  • How would you implement a 1-to-4 demultiplexer using two cascaded 1-to-2 demultiplexers?
  • Which term describes memory that retains data without power and is used for firmware?
  • Which symbol indicates an input or output operation in a flowchart?
  • Which base is used by the octal numeral system?
  • What is another name for a serial in/serial out register?
  • What is the function of a 2-to-1 multiplexer in this datapath?
  • Which output line is high for a 3-to-8 decoder with inputs A=0, B=1, C=1?
  • In binary addition, overflow occurs when the carry into the most significant bit differs from the carry out of the most significant bit.
  • What is the basic operation of an SR latch built with NOR gates?
  • For a JK flip-flop, which input condition causes Q to toggle on the clock edge?
  • A NOR gate can be described as
  • Which CPU function interfaces the computer with peripheral devices?
  • Which statement about ROM is true?
  • Simplify the Boolean expression f = A'B + AB' + AB.
  • The +5v level TTL is called a logical
  • Which memory type allows updating data by removing and rewriting individual bytes and is sometimes used for firmware storage?
  • The set of numbers that a number system is based on is called
  • According to the material, The Arithmetic Logic Unit is the control element of the entire microprocessors.
  • Which diagrams are the most convenient from which to learn the basic function of a circuit?
  • How does a T flip-flop behave for T = 1?
  • A logic pulser injects a 1 or 0 into a circuit
  • Which statement about ENIAC is true?
  • An instruction cycle is?
  • Which symbol is typically used to denote the start and end of a flowchart?
  • When counters are referred to by circuit design, they are called
  • In a 2-to-1 multiplexer, if the select input S is 0, which data input is forwarded to the output?
  • What is the basic unit of information in digital electronics that can be either 0 or 1?
  • What is the basic type of removable (replacable) memory you will find in standard desktop computers?
  • What element shows the direction of flow in a flowchart?
  • What is the truth table for a 4-to-16 decoder?
  • The main component in an inverter circuit is the
  • In a finite-state machine, which statement correctly characterizes Moore and Mealy machines?
  • Which statement correctly distinguishes ROM from RAM?
  • In a 3-to-8 decoder, with inputs A=0, B=0, C=1, which output is high?
  • Which element marks where a process begins and ends?
  • In ESD control, where should the resistance in the benchtop ground cable be located?
  • Which statement about PROM is true?
  • What does a 2-to-4 decoder do in the datapath?
  • Which diagram type is described as block or single line?
  • Which statement best describes a flowchart?
  • For a 3-input NAND gate, if all inputs are high, the output is
  • If precise timing is required, the clock generator will usually use?
  • What is clock skew and its effect in synchronous systems?
  • In standard flowchart symbols, which shape is used to represent a process step?
  • To realize a 2-Bit Register Using Flip-Flops, How Many Flip-Flops Are Required?
  • Which of the following is an advantage of EAROM memory over EPROM?
  • A byte consists of eight bits.
  • What is typically used to connect steps and indicate sequence in a flowchart?
  • What is clock gating used for?
  • A UART permits communication between an MCU and devices using other data formats and timing
  • What is a ring counter and its typical sequence with n flip-flops?
  • Define static hazards and dynamic hazards; provide an example of each.
  • Which device is commonly used to monitor a digital circuit and indicate high/low logic levels but does not drive the circuit?
  • Why are differentiators used as part of digital circuitry?
  • (A + B) + C is the same as?
  • Which register holds the address of the next instruction to be executed?
  • Explain static-1 hazard in the two-level implementation f = AB + A'C and how to mitigate. Which statement is most accurate?
  • Which statement about flow charts is true?
  • ESD Shunt diodes perform which function in a circuit?
  • The logic NOT symbol is also called
  • Extended Binary coded decimal interchange code (EBCDIC) is a _____ bit character encoding.
  • In an MCU the program is usually stored in the
  • Which property explains why (A + B) + C equals A + (B + C)?
  • What are the three basic requirements of timing pulse?
  • Which of the following is the clompic circuit?
  • In base-2 notation, when the exponent increases by 1, what happens to the value?
  • Which symbol is commonly used to represent input and output operations?
  • A Johnson counter with n flip-flops has a sequence length of how many states?
  • Contamination delay is defined as which of the following?
  • EAROM memory is described as being electrically alterable. Which characteristic is associated with EAROM?
  • In the described datapath, where does the address input go?
  • Convert 622 to hex.
  • In a D flip-flop, what value is loaded into Q on the clock edge?
  • Which statement is false about ESD protection diodes?
  • Circuits that perform boolean logic operations are called
  • How is the choice of which register is loaded communicated to the datapath?
  • Which symbol denotes a decision point in a flowchart?
  • Which symbol is not a standard flowchart symbol?
  • The number of________ determines the number of pulses to cycle a counter from 0 count to 0 count.
  • Hazards in combinational circuits are typically caused by what phenomenon?
  • The binary number 100000 carries a decimal weight of what?
  • Which statement best describes ENIAC's place in computing history?
  • Convert 111001 to Gray code.
  • Which statement about ENIAC is true?
  • What is hexadecimal referred to
  • Which component is typically used to achieve precise timing in a clock generator?
  • Which description best matches ENIAC?
  • In an asynchronous ripple counter, what triggers the toggling of a given stage after the first stage?
  • In Karnaugh maps, what does wrap-around adjacency allow?
  • The number of stages determines the number of pulses needed to complete a cycle.
  • Which work surface presents an opportunity for electrostatic discharge (ESD) damage?
  • If a three-input NAND gate has all inputs low, the output will be
  • Which code is commonly associated with IBM mainframes and uses 8 bits per character?
  • Using only NAND gates, which sequence correctly realizes f = (A + BC)′?
  • What is metastability and how can it be avoided?
  • What is the primary purpose of a flow chart?
  • A data direction register
  • Which of the following describes a PIPO shift register?
  • Which symbol represents a NOT logic gate in standard digital circuit diagrams?
  • What is the purpose of timing diagrams in digital design?
  • Explain Karnaugh map grouping for a 4-variable function.
  • Which statement best compares TTL and CMOS logic in terms of speed and power?
  • What is the decimal value of hexadecimal 2E?
  • What is another name for a serial in/ serial out register?
  • How many registers are indicated in this tiny datapath description?
  • How would you implement a modulo-10 counter using 4-bit binary flip-flops?
  • How can glitches be minimized in a combinational circuit?
  • What is the role of the 2-to-1 MUX in this datapath?
  • What is the role of memory address lines in a ROM and how is data accessed?
  • āx3 is associated with which logic gate?
  • Which component is primarily responsible for performing logical operations on binary signals in a digital circuit?
  • When replacing a DIP chip, which safety measure is recommended?
  • The recommended ohmic value of an ESD wrist strap is approximately what?
  • In an MCU calculations are done by the
  • In what year was ENIAC completed?
  • What is the correct approach to derive a next-state table from a state diagram?
  • Given a state diagram, what is the correct method to produce a next-state table?
  • What does PLC stand for?
  • What type of diagram is most useful in learning the detailed component operation of a system?
  • Increasing the base-2 exponent by 1 results in which effect?
  • Which statement best describes PROM, PLA, and PAL in programmable logic devices?
  • Define propagation delay, contamination delay, setup time, and hold time.
  • MCU stands for?
  • The arithmetic logic unit is which of the following?
  • What is the bit-width of the register in the datapath?
  • How do a latch and a flip-flop differ in terms of clocking?
  • Which statement best describes the role of a flowchart?
  • Which statement best describes how a synchronous counter updates its state?
  • The expression Y = A applies to which device in digital logic?
  • Describe a 4-input priority encoder and its output behavior.
  • Show how to realize a full adder using two half adders.
  • A programmable logic controller (PLC) is primarily used for
  • In an EEPROM data can only be changed by erasing everything and starting over
  • Which component stores the current result or operands for ALU operations?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy